Tri-Star Glove
  • Home
  • About
  • IFR Face Masks
    • How to Wear a Mask
  • Gloves
    • Choose Your Glove by Cut Level >
      • A2 Cut Level
      • A3 Cut Level
      • A4 Cut Level
      • A5 Cut Level
      • A6 Cut Level
      • A8 Cut Level
      • A9 Cut Level
    • Thermal Protective Gloves
    • New ANSI Cut Levels
  • Low Lint Products
    • Low Lint Paint Gloves
    • Low Lint Paint Gloves with Cut Protection
    • Low Lint Anti-Static Paint Glove
    • Low Lint Paint Sleeve
    • Low Lint Paint Sleeve with Cut Protection
    • Low Lint Watch Covers
  • Cut and Puncture Protection
    • Garment Systems
    • Capes, Aprons, and Pants >
      • TSG-842-1 Cape Sleeve
      • TSG-785 Cape Sleeve
      • TSG-1111-2 Cape Sleeve
      • TSG-429 Over Pants
    • Sleeves and Specialty Items
  • Welding
    • Welding Capes and Bibs
    • Welding Jackets
    • Welding Aprons and Sleeves
    • Welding Pants and Bib Overalls
  • Molten
    • Primary Layer - Aluminized
    • Secondary Layer
  • Value Add
  • Technical
  • Contact Us
    • Watch Us Make Your Garment!
  • Employment Opportunities

TSG-842- Cape Sleeve 
with Cut and Puncture Protective Sleeves

Picture
Picture
Description
TSG-842-1 Tri-Star Glove cape sleeves provides both cut and puncture protection.  The cape is constructed with lightweight, breathable black polyester mesh that provides comfort to the team member.  

​The cut and puncture protective sleeves are constructed with Norfab® #366 fabric sewn with an inner layer of the same fabric above and below the elbow for additional protection. The cut resistant rib cuffs are constructed with Twaron® and Lycra® yarn with a well-designed thumbhole for safety. The stripes are sewn on with reflective 3M material. 
technical specifications
Constructed with CutPro® Vintage #366 - Cut and Puncture Data

Cut Resistance - ASTM F2992-16 
3,064 grams = Cut Level A6

Puncture Resistance - EN388-03
61 N = Level 3

Abrasion Resistance Test: ASTM D3884-09 
(Taber; H18 wheel; 500 g. wt)  600 cycles = Level 2


Caution: This garment should not be worn in areas where flame or high heat is present.  While the sleeves are inherent flame resistant, the polyester mesh front and back are not.
product details
TSG-842-1
Cape sleeves are available in sizes small through 4XL.  Additional sizes are available upon request.
Norfab #366 Fabric Spec Sheet
 Proudly Made in the U.S.A. | 800-832-7101
customerservice@tri-starglove.com
  • Home
  • About
  • IFR Face Masks
    • How to Wear a Mask
  • Gloves
    • Choose Your Glove by Cut Level >
      • A2 Cut Level
      • A3 Cut Level
      • A4 Cut Level
      • A5 Cut Level
      • A6 Cut Level
      • A8 Cut Level
      • A9 Cut Level
    • Thermal Protective Gloves
    • New ANSI Cut Levels
  • Low Lint Products
    • Low Lint Paint Gloves
    • Low Lint Paint Gloves with Cut Protection
    • Low Lint Anti-Static Paint Glove
    • Low Lint Paint Sleeve
    • Low Lint Paint Sleeve with Cut Protection
    • Low Lint Watch Covers
  • Cut and Puncture Protection
    • Garment Systems
    • Capes, Aprons, and Pants >
      • TSG-842-1 Cape Sleeve
      • TSG-785 Cape Sleeve
      • TSG-1111-2 Cape Sleeve
      • TSG-429 Over Pants
    • Sleeves and Specialty Items
  • Welding
    • Welding Capes and Bibs
    • Welding Jackets
    • Welding Aprons and Sleeves
    • Welding Pants and Bib Overalls
  • Molten
    • Primary Layer - Aluminized
    • Secondary Layer
  • Value Add
  • Technical
  • Contact Us
    • Watch Us Make Your Garment!
  • Employment Opportunities